Command |
Description |
||
---|---|---|---|
Averaging ON/OFF |
|||
Restart averaging |
|||
Averaging factor |
|||
IF bandwidth |
|||
IF bandwidth |
|||
Clears the table of calibration factors |
|||
Clears data of calibration standards |
|||
S-parameter error correction state |
|||
Information about trace (calibration type, number of ports) |
|||
Calibration coefficient data |
|||
Selects one-path two-port method |
|||
Selects Response Open method |
|||
Selects Response Short method |
|||
Selects full one-port method |
|||
Selects Response Thru method |
|||
Enables calibration coefficients |
|||
Calibration kit selection |
|||
Calibration kit label |
|||
Remove or restore a calibration kit |
|||
Load |
|||
Open |
|||
Short |
|||
Thru |
|||
Capacitance C0 (Open) |
|||
Capacitance C1 (Open) |
|||
Capacitance C2 (Open) |
|||
Capacitance C3 (Open) |
|||
Offset delay |
|||
Max frequency |
|||
Min frequency |
|||
Waveguide height to width ratio |
|||
Media type |
|||
Inductance L0 (Short) |
|||
Inductance L1 (Short) |
|||
Inductance L2 (Short) |
|||
Inductance L3 (Short) |
|||
Standard label |
|||
Offset loss |
|||
Standard type |
|||
Offset Z0 |
|||
Measurement array of Load |
|||
Measurement array of Open |
|||
Measurement array of Short |
|||
Reflection measurement array of Thru |
|||
Transmission measurement array of Thru |
|||
Information about connected module |
|||
Auto-Orientation procedure |
|||
Auto-Orientation ON/OFF |
|||
Manual module orientation |
|||
Procedure of one-port calibration |
|||
Procedure of one path two-port calibration |
|||
Characterization number |
|||
Executes the confidence check |
|||
Load |
|||
Open |
|||
Short |
|||
Thru |
|||
One path two-port |
|||
Response Open |
|||
Response Short |
|||
Full one-port (SOL) |
|||
Response Thru |
|||
Calibration method query. |
|||
Calibration completion |
|||
Port extension ON/OFF |
|||
Values of "Frequency1" and "Frequency2" |
|||
Loss compensation ON/OFF |
|||
Value "Loss at DC" |
|||
Values of "Loss 1" and "Loss 2" |
|||
Electrical delay value |
|||
Frequency range configuration |
|||
"Loss at DC" value ON/OFF |
|||
"Loss1" and "Loss2" values ON/OFF |
|||
Measurement of Short or Open |
|||
Restart averaging between Short and Open |
|||
Complete measurements of Short or Open |
|||
Start frequency of user span |
|||
Stop frequency of user span |
|||
System Z0 |
|||
Number of cables in the list |
|||
Cable selection |
|||
Frequency at which cable loss specified |
|||
Cable loss |
|||
Cable velocity factor |
|||
Cable correction ON/OFF |
|||
Frequency array of the measurement points |
|||
Fixed frequency for a power sweep |
|||
Center frequency |
|||
Span frequency |
|||
Start frequency |
|||
Stop frequency |
|||
Segment sweep table |
|||
Number of points |
|||
Point delay |
|||
Sweep type |
|||
Frequency offset adjust ON/OFF |
|||
Continuous offset adjust ON/OFF |
|||
Adjust period |
|||
Executes adjustment once |
|||
Adjusted Port |
|||
Adjust Value |
|||
Frequency offset ON/OFF |
|||
Port offset data |
|||
Port offset settings |
Divisor |
||
Multiplier |
|||
Offset |
|||
Start |
|||
Stop |
|||
Reference source |
|||
Measurement result data |
|||
Data format |
|||
Operating frequency |
|||
Clears the reference value |
|||
Reference values data |
|||
Memorizes the reference value |
|||
Clears the table |
|||
Data table |
|||
Inserts a row into the table |
|||
Saves measurements to the table |
|||
Removes a table row |
|||
Saves the table into *.CSV file |
|||
Sets measured parameter |