Please enable JavaScript to view this site.

 Network Analyzers using RVNA and RNVNA software


note

This icon Read only indicates a read only command. This icon Write only indicates a write only command.

This icon Remote only indicates command(s) without equivalent softkeys.

Comments are in italics.


Calibration

Correction (ON/OFF)

SENS:CORR:STAT

System Z0

SENS:CORR:IMP

 

Calibration Kit

Calibration kit selection

SENS:CORR:COLL:CKIT

 

Edit Cal Kit (Calibration kit)

Label

SENS:CORR:COLL:CKIT:LAB

Standard Type

SENS:CORR:COLL:CKIT:STAN:TYPE

Standard Label

SENS:CORR:COLL:CKIT:STAN:LAB

C0 [e-15 F]

SENS:CORR:COLL:CKIT:STAN:C0

C1 [e-27 F/Hz]

SENS:CORR:COLL:CKIT:STAN:C1

C2 [e-36 F/Hz^2]

SENS:CORR:COLL:CKIT:STAN:C2

C3 [e-45 F/Hz^3]

SENS:CORR:COLL:CKIT:STAN:C3

L0 [e-12 H]

SENS:CORR:COLL:CKIT:STAN:L0

L1 [e-24 H/Hz]

SENS:CORR:COLL:CKIT:STAN:L1

L2 [e-33 H/Hz^2]

SENS:CORR:COLL:CKIT:STAN:L2

L3 [e-42 H/Hz^3]

SENS:CORR:COLL:CKIT:STAN:L3

Offset Delay [ps]

SENS:CORR:COLL:CKIT:STAN:DEL

Offset Z0 [Ohm]

SENS:CORR:COLL:CKIT:STAN:Z0

Offset Loss [GOhm/s]

SENS:CORR:COLL:CKIT:STAN:LOSS

F min, [MHz]

SENS:CORR:COLL:CKIT:STAN:FMIN

F max, [MHz]

SENS:CORR:COLL:CKIT:STAN:FMAX

Media

SENS:CORR:COLL:CKIT:STAN:MEDI

H/W (waveguide height to width ratio)

SENS:CORR:COLL:CKIT:STAN:HWR

Save To File Write only

MMEM:STOR:CKIT

Restore Cal Kit Write only

SENS:CORR:COLL:CKIT:RES

Load From File Write only

MMEM:LOAD:CKIT

 

Measurement of Calibration Standards (Calibration)

Open Write only

SENS:CORR:COLL:OPEN

Short Write only

SENS:CORR:COLL:SHOR

Load Write only

SENS:CORR:COLL:LOAD

Thru Write only

SENS:CORR:COLL:THRU

Cancel Write only

SENS:CORR:COLL:CLE

Apply Write only

SENS:CORR:COLL:SAVE

 

Response calibration (Open) Write only

SENS:CORR:COLL:METH:OPEN

 

Response calibration (Short) Write only

SENS:CORR:COLL:METH:SHOR

Calibration method:

Response calibration (Thru) Write only

SENS:CORR:COLL:METH:THRU

Remote only

Full 1-port calibration Write only

SENS:CORR:COLL:METH:SOLT1

 

One path 2-port calibration Write only

SENS:CORR:COLL:METH:ERES

 

Full 2-port calibration with scalar Thru Write only

SENS:CORR:COLL:METH:SOLT2

Calibration method query Remote only Read only

SENS:CORR:COLL:METH:TYPE?

 

Port Extension

Port Extension (ON/OFF)

SENS:CORR:EXT

Extension Value

SENS:CORR:EXT:PORT:TIME

Loss n (ON/OFF)

SENS:CORR:EXT:PORT:INCL

Loss n Value

SENS:CORR:EXT:PORT:LOSS

Frequency n

SENS:CORR:EXT:PORT:FREQ

Loss at DC

SENS:CORR:EXT:PORT:LDC

 

Auto Port Extension (Port Extension)

Method (Current Span | User Span | Active Marker)

SENS:CORR:EXT:AUTO:CONF

Frequency 1

SENS:CORR:EXT:AUTO:STAR

Frequency 2

SENS:CORR:EXT:AUTO:STOP

Include Loss (ON/OFF)

SENS:CORR:EXT:AUTO:LOSS

Adjust Mismatch (ON/OFF)

SENS:CORR:EXT:AUTO:DCOF

Open, Short Write only

SENS:CORR:EXT:AUTO:MEAS

Cancel

SENS:CORR:EXT:AUTO:RES

Apply

SENS:CORR:EXT:AUTO:SAVE

 

Autocalibration

Characterization

SENS:CORR:COLL:ECAL:UCH

Orientation (AUTO)

SENS:CORR:COLL:ECAL:ORI:STAT

Orientation (Port А | Port В)

SENS:CORR:COLL:ECAL:PATH

Perform Auto-Orientation Write only

SENS:CORR:COLL:ECAL:ORI:EXEC

Characterization Info Read only

SENS:CORR:COLL:ECAL:INF?

Confidence Check Write only

SENS:CORR:COLL:ECAL:CHECK:EXEC

Calibrate

Full one-port calibration Write only

SENS:CORR:COLL:ECAL:SOLT1

One path 2-port calibration in both directions Write only

SENS:CORR:COLL:ECAL:SOLT2

THRU state Remote only Write only

SYST:COMM:ECAL:THRU

Impedance state of the specified port (Open | Short | Load) Remote only

SYST:COMM:ECAL:IMP

Temperature of the AutoCal module Remote only Read only

SYST:COMM:ECAL:TEMP:SENS?

 

Misc Calibration Commands Remote only

Clears the calibration coefficient table

SENS:CORR:CLE

Сalibration information Read only

SENS:CORR:TYPE?

 

Read/Write Measurement Data of Calibration Standards Remote only

Load

SENS:CORR:COLL:DATA:LOAD

Open

SENS:CORR:COLL:DATA:OPEN

Short

SENS:CORR:COLL:DATA:SHOR

 

Read/Write Calibration Coefficients Remote only

Selects the type of calibration before enabling calibration coefficients

Response calibration (Open) Write only

SENS:CORR:COEF:METH:OPEN

Response calibration (Short) Write only

SENS:CORR:COEF:METH:SHOR

Response calibration (Thru) Write only

SENS:CORR:COEF:METH:THRU

Full one-port calibration Write only

SENS:CORR:COEF:METH:SOLT1

Сalibration coefficient data array

SENS:CORR:COEF

Enables the written calibration coefficients depending on the selected calibration type. Write only

SENS:CORR:COEF:SAVE

Rev.:  24.1