Command |
Description |
|
|---|---|---|
Averaging |
Averaging ON/OFF |
|
Restart averaging |
||
Averaging factor |
||
IFBW |
IF bandwidth |
|
IF bandwidth |
||
Clears data of calibration standards |
||
S-parameter error correction state |
||
System error correction status |
||
Information about trace (calibration type, number of ports) |
||
Read/Write Calibration Coefficients |
Calibration coefficient data |
|
Selects one-path two-port method |
||
Selects Response Open method |
||
Selects Response Open and Short method |
||
Selects Response Short method |
||
Selects full one-port method |
||
Selects full two-port method |
||
Selects Response Thru method |
||
Enables calibration coefficients |
||
calibration kit selection |
||
SENS:CORR:COLL:CKIT:LAB |
calibration kit label |
|
SENS:CORR:COLL:CKIT:STAN:ARB |
Calibration Standard Definition |
Arbitrary impedance (Load) |
SENS:CORR:COLL:CKIT:STAN:C0 |
Capacitance C0 (Open) |
|
SENS:CORR:COLL:CKIT:STAN:C1 |
Capacitance C1 (Open) |
|
SENS:CORR:COLL:CKIT:STAN:C2 |
Capacitance C2 (Open) |
|
SENS:CORR:COLL:CKIT:STAN:C3 |
Capacitance C3 (Open) |
|
SENS:CORR:COLL:CKIT:STAN:COUN? |
Number of standards in the calibration kit |
|
SENS:CORR:COLL:CKIT:STAN:DEL |
Offset delay |
|
SENS:CORR:COLL:CKIT:STAN:FMAX |
Max frequency |
|
SENS:CORR:COLL:CKIT:STAN:FMIN |
Min frequency |
|
SENS:CORR:COLL:CKIT:STAN:LAB |
Standard label |
|
SENS:CORR:COLL:CKIT:STAN:LOSS |
Offset loss |
|
SENS:CORR:COLL:CKIT:STAN:L0 |
Inductance L0 (Short) |
|
SENS:CORR:COLL:CKIT:STAN:L1 |
Inductance L1 (Short) |
|
SENS:CORR:COLL:CKIT:STAN:L2 |
Inductance L2 (Short) |
|
SENS:CORR:COLL:CKIT:STAN:L3 |
Inductance L3 (Short) |
|
SENS:CORR:COLL:CKIT:STAN:TYPE |
Standard type |
|
SENS:CORR:COLL:CKIT:STAN:Z0 |
Offset Z0 |
|
Load |
||
Open |
||
Short |
||
Thru |
||
Calibration Method |
One path two-port |
|
Response Open |
||
Response Short |
||
Full one-port (SOL) |
||
Full two-port (SOLT) |
||
Response Thru |
||
Calibration method query. |
||
Calibration Completion |
Calibration completion |
|
System Impedance Setting |
System Z0 |
|
Auto-select Z0 ON/OFF |
||
System Z0 for the specified port |
||
Cable Correction |
Frequency at which cable loss specified |
|
Cable loss |
||
Cable velocity factor |
||
Cable correction ON/OFF |
||
Receiver attenuation setting |
||
Stimulus data |
||
Fixed frequency for a power sweep |
||
Center frequency |
||
Span frequency |
||
Start power |
||
Stop power |
||
Segment sweep table |
||
Sweep Time |
||
Number of points |
||
Point delay |
||
Sweep type |
||
