Please enable JavaScript to view this site.

 Network Analyzers using PXI software


note

This icon Write only indicates a read only command. This icon Read only indicates a write only command.

This icon Remote only indicates command(s) without equivalent softkeys.

Comments are in italics.


Frequency sweep

Start

SENS:FREQ:STAR

Stop

SENS:FREQ:STOP

Center

SENS:FREQ:CENT

Span

SENS:FREQ:SPAN

 

Sweep Setup

Points

SENS:SWE:POIN

Sweep Time

SENS:SWE:CW:TIME

Meas Delay

SENS:SWE:POIN:TIME

Sweep Type

SENS:SWE:TYPE

Reverse Sweep (ON/OFF)

SENS:SWE:REV

 

IF Bandwidth

IF Bandwidth

SENS:BAND

SENS:BWID

 

Power

Power (all ports)

SOUR:POW

Port Couple

SOUR:POW:PORT:COUP

Port Power (each port)

SOUR:POW:PORT

Slope

SOUR:POW:SLOP

Slope (ON/OFF)

SOUR:POW:SLOP:STAT

CW Freq

SENS:FREQ

RF Out

OUTP

 

Segment Table

Save...

MMEM:STOR:SEGM

Recall...

MMEM:LOAD:SEGM

Segment Display

DISP:WIND:X:SPAC

Segment Table

SENS:SEGM:DATA

 

Power sweep

 

Start

SOUR:POW:STAR

Stop

SOUR:POW:STOP

Center

SOUR:POW:CENT

Span

SOUR:POW:SPAN

 

Trigger

Hold

INIT:CONT

Single

INIT

Continuous

INIT:CONT

Hold All Channels

INIT:CONT:ALL

Continuous All Channels

INIT:CONT:ALL

Trigger Source

TRIG:SOUR

Trigger Scope

TRIG:SCOP

Restart

ABOR

 

Ext Trigger (Trigger)

Event (ON/OFF)

TRIG:POIN

Polarity

TRIG:EXT:SLOP

Position

TRIG:EXT:POS

Delay

TRIG:EXT:DEL

Route

TRIG:EXT:ROUT

 

Trigger Output (Trigger)

Trigger Output (ON/OFF)

TRIG:OUTP:STAT

Polarity

TRIG:OUTP:POL

Function

TRIG:OUTP:FUNC

Route

TRIG:OUTP:ROUT

 

Trigger Remote only

Generates the trigger signal

TRIG

*TRG

Generates the trigger signal; the command is pending until the sweep end

TRIG:SING

Waits for completion of all pending commands

*WAI

Sets the OPC bit of standard event status register upon completion of all pending commands

*OPC

Reads "1" upon completion of all pending commands

*OPC?

Current state of the trigger system

TRIG:STAT?

Waits for the specified trigger state to be reached

TRIG:WAIT

 

Frequency Offset

Frequency Offset (ON/OFF)

SENS:OFFS

Offset Type (Port | Source-Receiver)

SENS:OFFS:TYPE

Port #

(offset type)

Divisor

SENS:OFFS:PORT:DIV

Multiplier

SENS:OFFS:PORT:MULT

Offset

SENS:OFFS:PORT:OFFS

Start

SENS:OFFS:PORT:STAR

Stop

SENS:OFFS:PORT:STOP

Source

(offset type)

Divisor

SENS:OFFS:SOUR:DIV

Multiplier

SENS:OFFS:SOUR:MULT

Offset

SENS:OFFS:SOUR:OFFS

Start

SENS:OFFS:SOUR:STAR

Stop

SENS:OFFS:SOUR:STOP

Receiver

(offset type)

Divisor

SENS:OFFS:REC:DIV

Multiplier

SENS:OFFS:REC:MULT

Offset

SENS:OFFS:REC:OFFS

Start

SENS:OFFS:REC:STAR

Stop

SENS:OFFS:REC:STOP

Port offset frequency array Remote only

SENS:OFFS:PORT:DATA?

Source offset frequency array Remote only

SENS:OFFS:SOUR:DATA?

Receiver offset frequency array Remote only

SENS:OFFS:REC:DATA?

 

Offset Adjust (Frequency Offset)

Offset Adjust (ON/OFF)

SENS:OFFS:ADJ

Adjust Value

SENS:OFFS:ADJ:VAL

Adjusted Port

SENS:OFFS:ADJ:PORT

Auto Adjust

SENS:OFFS:ADJ:EXEC

Auto Adjust Path

SENS:OFFS:ADJ:PATH

Auto Adjust Period

SENS:OFFS:ADJ:CONT:PER

Rev.:  22.3